Prime Resins

Accessories

Flexible joint fillers used to fill movement joints in building and civil engineering.

  • blank
  • Product
  • Description
  • TDS

Products

Description

This gun, manifold and adapter allows you to connect to a common pipe thread on your probe from a fixed ratio plural pump. The housing holds a 48 element 1/4″ static mixer and features a cutoff ball valve to eliminate back pressure when disconnecting the adapter.Gun w/ Whip Hoses- Item #FG-PG-0007 Pipe Adaptor- Item #FG-PG-0001

Description

As you inject chemical grout through pipes, you may need assistance in raising a pipe out of the ground. Our pipe jack has been modified to maximize compatibility with this application. Item #PIPE-JACK

Description

Used in conjunction with 3/4″ pipes. The drive point provides a pointed end to help the pipe penetrate the ground and to keep soil and debris out of the pipe. Once the pipe is in place, it can be raised a few inches to drop the expendable drive point and allow the chemical grout to flow freely. Item #DP-34

Description

EZ Couplers (Reducer, Union, EZ Tube, Zerk Adaptor) Connects the 1/4″ static mixer from our Quick Mix cartridges directly to our injection ports (or tubing from hard to reach places). The connection reduces resin drip and allows the operator to concentrate on the injection process rather than on trying to keep the static mixer in the port. Reducer- Item #QMR-5, Union- Item #QMU- 5, EZ Tube – Item #QMT-14, Zerk Adaptor – Item #QMC–Z

Quick Mix Reducer Ball Valve Connects the 1/4″ static mixer from our Quick Mix cartridges directly to our low pressure injection ports. The ball valve can be closed to reduce waste when moving from port to port.Item #QMR-BV

MIXERS

1/4″ x 32 Element Mixers (for injector resins) 10 per pack Packaged standard with Prime Re 1000, 1100, 1200, 1900; Prime Flex 900 XLV, 920, and Hydro Gel SX Item #740

1/4″ x 48 Element Mixers (for Prime polyureas) 10 per pack Packaged standard with Floor Fix 10, and Prime Flex 985 Fast Item #741

1/2″ Static Mixer (For Epoxy Gels) 10 per pack Packaged standard with Prime Rez 1600, Joint Shield 5000 Semi Rigid caulk grade, 5200 and all Prime Gel epoxy adhesives Item #760

Static Mixer Retainer Nut Item #QM-RN

High Pressure Coupler These couplers are perfectly matched to provide the tightest seals when used with our mechanical packers or Bang-In Ports. Item #680 or 680-CB (with Check Ball)

Description

3/8″ & 3/4″ Soil Probes These strong, durable soil probes are constructed of high-strength stainless steel. Just screw them onto either 3/8″ or 3/4″ pipe and drive them into the soil with a pneumatic driver. The resin flows through the pipe and out of the holes drilled in the diffuser section of the probe. Item #SP38, SP34

Description

1/2″ Mechanical Packers – Item #500 1/2” expanding port, orange in color, For high pressure. 100 / box. APPLICATION: Injection of chemical grouts and epoxy resins in sound or deteriorating concrete. Packer neck requires 3/8” or 10mm socket wrench, zerk fitting requires 9/32” zerk driver (Item #ZD516).

1/2″ Mechanical Packers – Item #550 1/2” expanding port, red in color, For high pressure. 100 / box. APPLICATION: Injection of chemical grouts and epoxy resins in sound or deteriorating concrete. Packer neck requires 1/16” or 14mm socket wrench, zerk fitting requires 5/16” or 8mm socket wrench.) (Item #ZD550).

5/8″ Mechanical Packers – Item #625 5/8” expanding port, yellowgreen in color, For high pressure. 100 / box. APPLICATION: Injection of chemical grouts and epoxy resins in sound or deteriorating concrete. For deep drilling. Packer neck requires 3/8” or 10mm socket wrench, zerk fitting requires 9/32” zerk driver (Item #ZD516).

3/8″ Bang-In Ports- Item #640 3/8” tapered port, threaded zerk fitting, for high pressure. 100 / bag. APPLICATION: Injection of chemical grouts and epoxy resins in new or sound concrete. Zerk fitting requires 5/16” zerk driver (Item #ZD932).

One Touch Packer – Item # OTP-10MM Unique, patented construction eliminates costly extraneous metal pieces, replacing time consuming zerk fittings with an interior check valve that opens only while chemical grout/epoxy is being injected. APPLICATION: Injection of chemical grout and epoxy resins in new or sound concrete.

Description

Plastic Surface Mount Ports – Item #652 with Attached Plastic Cap Surface mount port. Large opening for static mixers. Low pressure only. 100 / bag (includes cap). Application: For use with 1/4″ or 1/2″ static mixers and Prime Rez 1600 injection gel.

Plastic Surface Mount Ports – Item #653 Y-shaped base, Low pressure only. Will accept cartridge systems and other pressure injection equipment. 100 / bag. Application: Epoxy injection. (Requires #662).

Plastic Corner Mount Ports – Item #655 Low pressure only. Will accept cartridge systems and other pressure injection equipment. 50 / bag. Application: Epoxy injection. (Requires #662).

Socket Mount Ports – Item #660 For 1/2″ holes. Low pressure only. Will accept cartridge systems and other pressure injection equipment. 100 / bag. Application: Injection of chemical grouts or epoxy resins for either direct or offset injection. (Requires #662).

1/4″ Caps for Plastic Ports – Item #662 100 / bag. Application: Required for use with #653, 655, 660. Used to close port after injection.

Description

StainShield concrete protector shields surfaces from resin and epoxy stains. Use this concentrate diluted with water to reduce or eliminate the discoloration from, polyurethane lifting foams, polyurethane or epoxy grouts, and polyurea or epoxy joint sealers. These foams, grouts and sealers normally leave a discolored area on the surface of contacted concrete. This discoloration is exposed when removing inadvertent overflow from cracks, joints or drilled holes. This discoloration is often unsightly in an otherwise flawless project. Recommended as a protective concrete stain barrier when using polyurethane, epoxy or polyurea systems. Aids in overfill cleanup by allowing easier removal of excess material. Biodegradable with low toxicity.

Description

Dry oakum is used to form surface seals and helps control gushing leaks during injection. It can also be used in combination with Prime Flex 900 XLV and Hydro Gel for the Activated Oakum method of sealing joints and pipe penetrations. Prime Resins oakum comes in 50 lb. or 10 lb. boxes. The oakum can be unraveled to produce additional feet of smaller strands. Item #690 – specify 10 or 50 lbs.

Description

Prime Plug is a rapid-setting concrete patching material designed to cut off water leaking through concrete or masonry surfaces. Stops water flow through concrete or masonry. Used in conjunction with Prime Flex products for a permanent solution. Typical areas of use include manholes, pipes, tanks, tunnels, utility vaults, elevator pits and dams. Exhibits excellent bond strengths and high early strengths. Available in three different set times. Stops gushing leaks and is non-shrink. Set times are 1-2 minutes for Prime Plug 1 (red top), 3-5 minutes for Prime Plug 2 (blue top), and 8-13 minutes for Prime Plug 3 (blue top).

Description

Our proprietary catalyst used to adjust the reaction time of Prime Resins’ hydrophobic polyurethane injection resins, including Prime Flex 910, 920 and 940. It is used in a concentration between 1/2% to 10%, depending on the desired reaction time.

Description

Kick Fast is the catalyst needed when a very fast set time is required when using Prime Resins’ hydrophobic polyurethane injection resins. It is used at 10% concentration to ensure a very fast set time. Extremely cold water or high hydrostatic pressure are two examples of situations where Kick Fast is the appropriate choice.

Description

If you are doing high-pressure injection, this inexpensive tool is a must. Use it to reach the back of your drilled holes and flush out concrete dust so that it doesn’t contaminate the crack during injection. Item #670

Description

This 1/4″ stainless steel grout needle is 12″ long. Use it to penetrate rubber boot seals for leak sealing at the manhole-pipe connection. It is also good for injecting Prime Flex polyurethane behind an activated oakum seal. We also offer a model that attaches directly to the mix nozzle of our Quick Mix and Single Shot cartridges. Other lengths available upon request. Needle – Item #674, Quick Mix Kit – Item #675

Description

The wall stinger nozzle attachment screws directly on top of the “F” Valve Assembly. It allows injection of chemical grout directly through a concrete structure without the need for an injection port. This is ideal for grouting behind a manhole or a below-grade wall. Not recommended for high-pressure crack injection. Item #WS-NOZ

Description

This is the only accessory required to turn an airless sprayer into an injection pump. It allows the operator control of resin flow at the point of injection. High Pressure valve. Up to 4,500 psi. Item #685-H

Description

Eco Flush is a non-flammable solvent great for cleaning equipment and flushing out pump cylinders, lines, and hoses after Prime Flex injection. The special blend of solvents is designed for flushing and cleaning Prime Flex polyurethane and Prime Rez epoxy injection resins out of injection pumps and hoses. Item #99-5P

Description

Prime Conduit Seal Kit is a quick and convenient method of stopping water seepage around pipe penetrations or around cable in conduit. Kit includes 8 pair of rubber gloves, 1 liter of Prime Flex 900 XLV in a measuring bottle, 8 bags of dry oakum (12″ strip in each bag), one 2-gallon plastic water bucket, and directions for completing repair. Item #CDSK

Description

The DM500 is a compact manifold that delivers two independent streams of material into a 1/2” static mixer before entering a single material hose. This allows the operator to move from one location to the next without having to lug around multiple hoses. The DM500 has an integrated flush system which allows you to flush both the manifold and attached dispense hose and valve/gun. It can be used to mix most of our slow set polyurethanes, polyureas and epoxies. Item #DM500

Description

Cleans cured grout from injection equipment. It is non-chlorinated, nonflammable (by U.S. DOT definition), non-carcinogenic, and non-ozone depleting. Can be used for extended periods, tolerate high resin loadings, and will reduce disposal costs. It is also recyclable via vacuum distillation.

Description

The F Valve assembly is a low cost valve assembly that was designed to “twin stream” Prime Flex polyurethanes with water. The mix ratio is controlled by the operator using the two on/off valves that come with the assembly. This is especially useful for injecting Hydro Gel into leaking manholes. High pressure valve. 2000 psi and under. Use with grout needle kit or wall stinger nozzle. Available in stainless or carbon steel.